Water connection

(This feature is optional)

NOTICE

notice

WARNING

The product and the water pump, if any, must be unplugged during connection.

 

The mains, filter and carboy connections of your product must be made by an authorized service center.

Depending on the model, you can connect your product to a carboy or directly to the water network. To make this connection, you must first connect the water hose to the product.

Depending on the model of your product, check whether the following parts are included with the product:

  1. Union (1 piece) : Used for attaching the water hose to the back of the product.
  2. Hose clip ( 3 pieces ) : Used for fixing the water hose to the wall.
  3. Water hose (1 piece, 5 meters diameter 1/4 inch): Used for making water connections.
  4. Faucet adapter ( 1 piece ) : Used for cold water mains line connection with porous filter. 
  5. Water filter (1 piece *Optional): It is used to connect the mains water to the product. If there is a carboy connection; there is no need to use a water filter.

Connecting the water hose to the product

Follow the instructions below to connect the water hose to the product.

  1. Remove the fitting from the hose end adapter attached to the back of the product, thread the fitting onto the water hose.
  2. Attach the water hose to the hose-end adapter by pressing down firmly.
  3. Secure the union to the hose-end adapter by hand tightening. You can tighten the union using a pipe wrench or pliers.

Connecting to mains water 

(This feature is optional)

If you are going to use the product by connecting it to the cold water line, you need to install a standard 1/2" valve fitting on the cold water network in your home. If this fitting is not available and you are not sure, consult a qualified plumber.

  1. Disconnect the union from the faucet adapter.
  2. Connect the faucet adapter to the mains line valve. 
  3. Thread the union onto the water hose.
  4. Thread the union onto the faucet adapter and tighten by hand/tool. 
  5. Secure the water hose in suitable places with the clips provided to prevent damage, slipping or accidental dislodging.

NOTICE

notice

WARNING

After opening the faucet, make sure that there is no water leakage at both joints of the water hose. In case of leakage, close the valve immediately and tighten all joints with a pipe wrench or pliers.

For products to be used in carboys;

(This feature is optional)

In order to connect carboy water to the product, the water pump recommended by the authorized service is required. 

In order to connect carboy water to the product, the water pump recommended by the authorized service is required. 

  1. After connecting one end of the water hose from the pump to the product, follow the instructions below.
  2. Make the connection by pushing the other end of the water hose into the water hose inlet of the pump.   
  3. Secure the pump hose by placing it into the carboy.
  4. After completing the connection, plug the pump into the socket and start the pump.

NOTICE

notice

After starting the pump, wait 2-3 minutes for it to reach the desired efficiency.

NOTICE

notice

Refer to the instruction manual of the pump while making the water connection.

NOTICE

notice

If carboy will be used, there is no need to use a water filter.

Water filter

(This feature is optional)

Depending on the model, your product may have an external or internal filter. To install the water filter, follow the instructions below.

Mounting the external filter on the wall

(This feature is optional)

NOTICE

notice

WARNING

Do not install the filter on the product.

Depending on the model of your product, check whether the following parts are included with the product:

  1. Union (1 piece) : Used for attaching the water hose to the back of the product.
  2. Faucet adapter ( 1 piece ) : Used for cold water mains line connection.
  3. Porous filter ( 1 piece )
  4. Hose clip ( 3 pieces ) : Used for fixing the water hose to the wall.
  5. Filter connection apparatus ( 2 pieces ): Used for mounting the filter on the wall.
  6. Water filter (1 piece): It is used to connect the mains water to the product. If there is a carboy connection; there is no need to use a water filter.
  7. Connect the faucet adapter to the mains line valve.
  8. Determine the place where the external filter will be fixed. Mount the filter connection apparatus ( 5 ) on the wall.
  9. Attach the filter perpendicularly to the filter bracket as indicated on the label. ( 6 ).
  10. Connect the water hose coming out of the top of the filter to the water connection adapter of the product.
  11. After the connection is completed, the image should be as shown below.

Since the internal filter that comes in the product does not come installed, the necessary procedures for its preparation are as follows:

Water line

Carboy line:

NOTICE

notice

Do not use the first 10 glasses of water after connecting the filter.

  1. For filter installation, the “Ice Off" indicator must be active. Switching between ON and OFF indicators on the display is done by pressing the “Ice” button.
  2. Remove the crisper compartment to access the water filter.
  3. Remove the water filter by-pass cover by pulling it towards you. 

  4. NOTICE

    notice

    It is normal for a few drops of water to come out after the cover is removed.

  5. Insert the water filter cover into the mechanism and push it forward to lock it in place.
  6. Exit the “Ice Off” mode by pressing the "Ice” button on the display again.

NOTICE

notice

The water filter removes some foreign particles from the water. It does not purify the water from microorganisms.